Trouts & Stouts
 
While this past weekend did not afford an opportunity to fish, there were a few free hours to devote to some of my lingering projects. So, I began to work on my bamboo rod rebuild in earnest. This is my first attempt at doing anything with bamboo, but it seems that the basic steps are the same as they would be for rebuilding any rod. 
Picture
Step 1: Documentation

Before doing anything to the rod, I took photographs of each piece and recorded all of the pertinent measurements, including number of guides, guide spacing, wrap color and style, and handle configuration.

The most notable thing about this particular rod, is that it was originally intended to be usable as either a fly or spinning rod. In the fly rod configuration, it is an 8 foot three piece rod with two tips. However, there is a third tip that fits into the but section to make a shorter spinning rod. In the spinning configuration, the handle and reel seat can be completely detached and reversed to accommodate a spinning reel.
Step 2: Research

There are few extant markings on the cane, but I suspected that it might be a Montague or other production rod. But, after consulting with some knowledgeable folks, I determined that, due to it's hardware, it was probably a post-WWII Japanese rod. Not collectable, but highly fishable.
Picture
The remains of the rod's original decal.

Step 3: Disassembly
Using care not to mar the cane, I used a single-edged razor blade to remove the guides and as much of the thread wraps as possible. The wraps on the guides and ferrules came off without much trouble, but the long intermediate wraps were worn in many places, and proved much more difficult. Ultimately, I left about half of them on, hoping that they would be removed in the next step.

As the reel seat and grip are in good condition, and as they can be removed completely as a unit, I simply set them aside for the time being.

I would have opted to keep the original ferrules on the rod, but they seem to be made of a soft chrome-plated metal and at least one of them was badly bent, which at first led me to believe (mistakenly) that the cane had taken on a significant "set". I removed the ferrules by heating them slowly over a candle, taking care not to scorch the cane. After several minutes and a few tugs with pliers, they each came free without marring the cane.
Picture
Step 4: Stripping

After some research, I found that the "natural" citrus based Citristrip that I use on fiberglass rods could be used to strip the varnish off of cane without damaging the glue that binds each individual strip of bamboo together into a tapered blank. Over the course of a day I submitted to cane to four treatments, which succeeded in removing all of the remaining thread, but only about half of the varnish.
I am going to experiment with some light sanding and maybe more lengthy treatments to try to get as much varnish off as possible without harming the blank. Once I have a completely clean blank, it will be time to start building the blank back up to a fishable rod.

--Posted by Eben
 
 
It has been pretty busy here project-wise. I've just rounded up work on a series of fiberglass rods and I think I am going to be switching gears for a few weeks to some new projects. 
Picture
Eclectic Angler Bi-Metal Reel

For Christmas I received a kit to build a this neat little brass and aluminum reel. The kit is manufactured by fellow Massachusetts-er  Michael Hackney at Eclectic Angler. In addition to making ands selling classic fly reels and kits, Michael is the author of The Reelsmith's Primer, and  administers an online forum for reelsmiths. 

The kit itself includes pre-cut reel pieces, and other components to finish and assemble. I have not done a lot of metal working, but I think I should be able to handle the polishing and filing required.

Picture
Orvis Hydros Graphite Fly Rod

One of my personal projects of the last couple of years is getting my friends involved in fly fishing. One of my recent success stories has been my friend Ned, who has come on more than one fishing excursion, including last year's excellent trip to the Tuolumne river in Yosemite. He has enjoyed it enough that it is time that he had his own rod. I am honored that he is trusting me to build it for him. I am not a lover of graphite, but as a former Orvis retail associate I can say that they make some pretty rods, especially for a beginner. Therefore, I am going to build him a 8.5 ft, 5wt Orvis Hydros. Orvis finishes these out with a a lovely blue thread and aluminum reel seat, but at Ned's request, I think we will be using a more traditional wooden reel seat, and a contrasting thread.

Picture
Unknown Bamboo Production Rod Restoration

My Dad picked up this bamboo rod last year at an antique store, and fished it for a couple of months before the stripping guide came off and it was clear that the rod was in need of some serious TLC. After consulting some knowledgable folks, I have determined that it is a post WWII Japanese rod, and probably has little collector's value. Therefore I am going to modernize it for fishing, upping the number of guides from 6 to 8, and replacing the bent chrome ferrules with nickel-silver.

 
 

Granger Bamboo

River Report

The lower Stanislaus river below goodwin dam: 3/22/10. Flow 340 CFS. Sunny and 70 degrees
It was odd day on the Stan. First off there was no other anglers there but me. That was the amazing part of this much needed river sojourn that happened to be doubling as a much needed mental health day. I had my eight and a half 5/6 wt bamboo hardy with me, which I've decided is totally inappropriate for this river, its too full flex for nymphing. When I got to the hot spot under the dam, I noticed two gentlemen in dive gear. They were from a private company called fish-bio, and they were shooting footage of wild trout. We had a friendly exchange on the river bank. They confirmed the rumor about the presence of large steelhead in the river. The rest of the day kind of defied expectation, especially in light of the data nature was giving me about how fish should of been responding. There was a tremendous may fly hatch, that lasted hours, and in the background behind that there was the usual midge activity. Despite the biomass there was scarcely a trout around to rise to these abundant insects. I must of spent hours in a spot where I know fish stack up. Nothing was working. I did miss a bunch of strikes, not because I didn't see or feel them, but rather because the bamboo I was using was not firm enough to allow for a fast hook set in current. A modern gear head might argue that this is another example of why graphite is superior, to which I would counter by telling him my 6wt Phillipson is being repaired. I'd probably also think to myself that he has no sense of aesthetics, and that artfulness is apart of catching fish by god!  I digress. 
I picked up the smallest trout I've ever caught on the Stan on a #20 zebra midge, that that happened after 4hrs. I decided that--hell--I'm fishing a british rod, might as well fish English. I tied on three soft hackles in tandem, and took off my indicator. This proved to be a good move--a nice 14" bow slammed my middle fly. At least I knew now, where they were feeding in the column. At this  point I had worked hours and hours in a proven spot for just 2 fish. I broke for lunch. I get board of fishing in the same spots, and it has always amazed me why other anglers don't--odd. I decided to fish further down by the cable pool, per the fish-bio divers suggestion. I've fished this spot before to no avail, and it was no different this time. It was beautiful and very warm by this point as it was mid day, and not typically a good time to fish, as the sun was at it's zenith. The interesting and majestical thing about the Stan is that it is in a deep confined canyon, and up by the dam the sun has a harder time penetrating. The sun factor coupled with a lovely fine mist--makes for a pleasant spot to fish as the rest of the river heats up. I'm one for new experiences, a wonderer if you will...always curious about whats down the road, or in this case the river. The dam hadn't been productive, and  I wasn't having any luck at the cable pool. In any event, I decided to have a look further down. I found a little animal path that took me quite a bit above the river onto a promontory be-speckled with spring wild flowers. Looking down I was wondering how I'd reach the river, as there was a very nice run, begging to fished. What happened next, I'm still thinking about... a little trout caught my eye, and next too him I got a good long look at a 20-24" rainbow, lazily picking stuff out of the current. The problem was he was on the same side of the bank that I'd be on once I got down there. I did in fact get down there and managed to cobble together the best cast I could to get at him, which unfortunately had to be right over the fish. This no doubt spooked him. I feel like these particular trout are very wary about what is above, as the canyon brings many birds of prey to a focal point. The potential of death from above, a bright mid day sun, and a cast straight over his back, no doubt put my wise quarry on high alert. 
My day was pretty much over. I tried in a few more spots, but was ultimately satisfied with the two I caught. More importantly then the fish, was the discovery of a new spot. I plan to return to it especially when the dam is crowed, as maybe I'll have another chance at a trophy.  
--Posted by David